How To Choose Rs485 Cable > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

We can gain insight into the operation of the RS232 protocol by examining the signal connections used for the primary serial port in Table 9 6. The transmit and receive data signals carry the messages being communicated between the QScreen Controller and the PC or terminal. By connecting pairs of these handshaking signals together, the terminal or PC can be made to think that the PDQ Board is always ready to send and receive data. This shield will be ideal for connecting your Arduino to any RS232 devices, and it is also stackable for multiple serial I/O ports! The shield includes female DB9 connectors for connecting to a variety of RS232-compatible devices. The DB9 socket uses three wires as shown on the diagram below. If handshaking is not necessary, an ordinary 4 wire telephone cable could be used, provided that the pins are cross-connected as shown in the picture below. Can you tell me what kind of test can we perform in order to determine if this cable needs to be replaced or is already working fine? After all, how would their device tell whether the binary bitstream it receives originated from a PC or any other device?

Your 485 to 232 converter should have some information in the manual to tell you what cabling is needed to connect it, but since you are asking, it obviously doesn't say, or isn't clear. I’ll see if I can find more information on the protocol. Read more about RS232. Rs232 is only an option for pc to controller. Otherwise RS232 would be my next best option. I guess if nothing else, I could use trial and error to find which one works; while not ideal, it may be my only option. I guess rs485 isn’t a basic standard across the board. RS485 isn’t really a protocol but the definition of the electrical characteristics of the link between nodes. I’m wanting to use the photon/electron for an rs485 cable replacement between two pieces of equipment, no computer on either end. We need to test the operation of a computer Belden cable RS485 for one of our clients. If your application requires RS485, you can use the secondary serial port (serial2) to program and debug your application code using the RS232 protocol, and use the primary serial port (Serial1) for RS485 communications. They use the digi xtend wireless modems, which are specifically made to be universal, per the manufacturers website (which I take to mean they probably use asynchronous serial communication).

One of the main reasons why this standard is used it's because wireless rs485 is able to send data a long distance. If you are planning to replace the cable between two existing RS485 nodes, you need a way to talk to the nodes on either side, and that would still be RS485. Now, I’m still not sure if I have all of the information needed to make a decision on this project, there is still quite a few assumptions being made with no evidence to be found to back it up; also none to dispute it. Based on information from the Wikipedia page you posted, it looks like there are a limited number of communication standards transmitted over 485, with one being pointed out as the most frequently used. At time of broadcast communication of the binary mode, returning of data is not executed except for the inverter to be returned (inverter number 00H) and when the inverter number is not matched. However, you can make the representative inverter in each block report the occurrence of a problem in the block. You need to find some datasheets/appliction notes to get that info too before being able to make a educated choice.

You'll need to determine how to set the address on the converter as well as figuring out what the address is on your RS485 device. Up to 10 WIRED PROs can be connected to SENSEWAY within a total range of 100m of RS485 cable. The basic rate is 54 Mb / s, but in practice works best in the range of 20 Mb / sRadio network in the case of district heating has proven to be an excellent alternative to other types of communication systems and in this application is an innovative solution. LAPP manufactures a range of Unitronic Serial RS485 Cable range. Finally check the documentation on your RS485 device to see how to set it up, and if can be disabled by default. If you can get a decent documentation about how to use TCP/IP that might be the easiest to go with. What protocol the two virtual-wire devices use to communicate with eachother is another thing and can be virtually anything. AI Devices) are only stating the "transport" but don’t really provide any detail about the protocol.